Yaralanma

The weight collars can fail to grip the dumbbell bar securely during use. This could result in weight plates coming loose or sliding off, particularly under vertical loading, leading to injuries. The product does not comply with the General Product Safety Regulation.

The adhesive bond between the closure strips and the bag film. As a result, the closure strips may detach partially or completely during use, causing the product to lose its intended function and potentially releasing the enclosed magnets. The magnets constitute small parts. A child can put them in the mouth and choke. Moreover, if a child swallows them, they could attract one another causing intestinal blockage or perforation. The product does not comply with the General Product Safety Regulation.

The UVA-A and AV-B radiation is not sufficiently filtered, posing possible eye damage to the wearer. Moreover, the goggles’ compressive strength is insufficient. The eyecups and strap retainers break, leading to injuries. The product does not comply with the Personal Protective Equipment Regulation (PPE).

The strength and the effectiveness of the helmet are inadequate. In the event of an impact, users may suffer head injuries, due to displacement. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

There is a defect in the wire gate riveting on these carabiners. This assembly fault could cause the gate to break or detach, posing a risk of carabiner failure in the event of a fall, leading to injuries. This product does not comply with Personal Protective Equipment (PPE) Regulation.

The welding is not sufficiently strong. The frame can therefore break apart due to the weakness at the centre of the bicycle frame. This could cause the rider to fall, which could lead to injuries. The product does not comply with the requirements of the Machinery Directive.

The strength and the effectiveness of the helmet are inadequate. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The strength and the effectiveness of the helmet are inadequate. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The gate of the carabiner can malfunction and may not close automatically. This creates a risk of unintended detachment during use, which could result in a fall from height. This product does not comply with Personal Protective Equipment (PPE) Regulation.

The product presents a serious risk of injuries as it is supplied with an attachable canopy. In windy conditions, the canopy could cause the product to lift from the water. The child could fall from the product and be injured by impact or by drowning in the water. The product does not comply with the General Product Safety Regulation.

Due to a structural failure, the handle bar can easily break. This could cause an accident and injuries. The product does not comply with the General Product Safety Regulation nor with the European standards EN ISO 4210.

Floating seats with leg openings must not have any overwater structures. In windy conditions, the float may be lifted, tipped over, pushed away, or destabilised, creating risks of falls, capsizing, separation from the caregiver, entrapment, or drowning. The product does not comply with the General Product Safety Regulation

The strap in front of the ear may slide backwards, which could affect the stability and optimal hold of the helmet on the head during normal use. In case of an accident this may lead to injuries. The product does not comply with the Personal Protective Equipment Regulation.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1078.

The strength and the effectiveness of the retention system of the helmet are inadequate. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1087.

The helmet fastener can easily open during a fall or accident, causing the helmet to slip off and potentially leading to head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1087.

Due to a software error, the pedals may reverse direction while the user is riding the bike, which could lead to injuries. The product does not comply with the requirements of the Machinery Directive.

Due to a software error, the pedals may reverse direction while the user is riding the bike, which could lead to injuries. The product does not comply with the requirements of the Machinery Directive.

Due to a software error, the pedals may reverse direction while the user is riding the bike, which could lead to injuries. The product does not comply with the requirements of the Machinery Directive.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1078.

Because of the design of the folding mechanism, the ventilation openings are too wide. In the event of an impact, the helmet may not provide sufficient protection to the head and users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1078.

A fatigue crack in the fork steerer tube may develop over time, which could cause the fork to fail during use, potentially leading to a fall and injuries to the user. The product does not comply with the requirements of the Machinery Directive.

The product has a sharp edge in the folding mechanism, which could wear away the insulation of the product wiring over time and cause the bike to fail during use, potentially leading to injuries to the user. The product does not comply with the requirements of the Machinery Directive.

The carabiner's turn lock sleeve may malfunction and detach during use, leading to the user falling from a height and suffering injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The chin strap buckle can easily open, leaving the user unprotected in the event of an impact, causing injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1078.

The impact absorption capacity of the helmet is insufficient. Moreover, the strength and the effectiveness of the retention system are inadequate. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1087.

The chin strap buckle can easily open, leaving the user unprotected in the event of an impact, causing injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1078.

The product is not sufficiently stable. A crank arm may break and the cyclist may fall as a result and be injured. The product does not comply with the General Product Safety Regulation.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The carbon rims may have internal cracks that can lead the rims to break or deform. If a relevant load is placed on the bicycle this can cause the user to fall and be injured. The product does not comply with the General Product Safety Regulation.

The equipment is used together with a free‑fall auto‑belay device, which can cause the equipment to be propelled toward the user’s face, resulting in injury. The product does not comply with the Personal Protective Equipment Regulation.

The pedal axles can crack during use. This may cause the pedal to detach unexpectedly, causing the user to fall and leading to a risk of injury. The product does not comply with the General Product Safety Regulation.

The handle of the product can fail during use. The user can therefore fall and suffer injuries. The product does not comply with the Personal Protective Equipment Regulation.

One of the top screws that fixes the handlebars to the stem could easily break, which could cause the handlebars to rotate and the cyclist losing balance and falling, causing injuries. The product does not comply with the General Product Safety Regulation nor with the European standard EN 4210-2.

Premature screw wear at the gated ventral attachment point could cause the attachment point to accidentally come open during use. This could lead the user to fall and suffer serious or fatal injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The product lacks self-locking mechanisms on the different board, which can cause them to come loose during use, posing a risk of injuries to the child's hands and fingers. Moreover, the product lacks stability and can tip over during use, leading to a child falling off and suffer a concussion. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-8.

The fork might delaminate causing it to brake due to hard braking force, the cyclist may fall and suffer injuries. The product does not comply with the General Product Safety Regulation.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1078.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1078.

The retention system of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

Tears and cracks may appear during the expected lifetime of the product, which may result in loss of control of the skis. This may cause the user to fall and create a risk of injuries. The product does not comply with the General Product Safety Regulation.

If a baby is placed in the swim float with the canopy attached, a gust of wind could lift the product off the water. This can cause the baby to be dropped at height, causing injuries. The product does not comply with the General Product Safety Regulation.

If a baby is placed in the swim float with the canopy attached, a gust of wind may lift the product off the water. This can cause the baby to be dropped at height, causing injuries. This product does not comply with the General Product Safety Regulation.

If a baby is placed in the swim float with the canopy attached, a gust of wind may lift the product off the water. This can cause the baby to be dropped at height, causing injuries. The product does not comply with the General Product Safety Regulation.

Handlebars were incorrectly fitted, therefore, the holes for the integrated cabling may work incorrectly, leading to the breakage of the handlebar. This could cause injuries and cuts to the user. The product does not comply with the General Product Safety Regulation.

The fork of the bicycle could crack and break. This could cause an accident, leading to the injuries. The product does not comply with General Product Safety.Regulation.

The anchor's resistance to load is insufficient. If a climber uses the anchor when climbing, there is a risk that the anchor won’t be able to stop a potential fall and the climber is therefore exposed to the risk of insufficient fall arrest when taking a fall and the consequences may be severe injuries. The product does not comply with the General Product Safety Regulation.

The outer carbon layers of the bicycle wheels delaminate easily during use. This may cause the wheel rim to fail, leading to serious falls and injuries. the product does not comply with the General Product Safety Regulation

The toy has sharp protruding parts; which could cause injuries to the child, including eye damage. The product does not comply with the requirements of the Toy Safety Directive nor with the European standards EN71-1 and EN 71-8.

The shock-absorbing capacity of the kneepads is insufficient. As a result, the user might suffer injuries in case of an impact. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 14120.

The range of extension of the artificial wrist is excessive, which makes the wrist guard ineffective in the event of a fall and may cause injuries to the user. The product does not comply with the Personal Protective Equipment Regulation (PPE) nor with the European standard EN 14120.

The product lacks labelling information and instructions of use. Therefore, the user may set it up incorrectly, leading the product to detach or break during use and to cause injuries to the user. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The leg loop of the harness may tear out at the seam. This places the user at a risk of falling from height and sustaining serious injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation, nor with the European standard EN 12277.

If the red crank handle used to adjust height is removed during use or handling of the product, the post may fall vertically, causing injuries. The product does not comply with the General Product Safety Regulation.

The electric bicycle, its battery charger, cable and plug have not been manufactured to the required standards. If the product was left plugged in overnight, the battery could explode and cause a fire. The product does not comply with the requirements of the Machinery Directive.

The handlebar can easily break due to its low mechanical strength. The child can therefore lose control of the bicycle and fall, resulting in injuries. The product does not comply with the General Product Safety Regulation nor with the European standard EN 8098.

A spontaneous delamination, separating the carbon layers, of the rim flange may occur, significantly compromising the wheel’s structural integrity. Due to this damage, there is an increased risk of accidents. This product does not comply with the General Product Safety Regulation.

The shock-absorbing capacity of the helmet is insufficient. As a result, the user might suffer injuries in case of an impact. The product does not comply with the Personal Protective Equipment Regulation.

The product lacks labelling, safety information and instructions of use. Therefore, the user may set it up incorrectly, leading the product to detach or break during use and to cause injuries to the user. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The product can fail to retract during use. This could cause the user to fall unexpectedly from a height. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

A spontaneous delamination, separating the carbon layers, of the rim flange may occur, significantly compromising the wheel’s structural integrity. Due to this damage, there is an increased risk of accidents. This product does not comply with the General Product Safety Regulation.

The product may resemble a toy; however, there is a risk of drowning if children play with it unsupervised. Floating seats with leg openings must be used under constant adult supervision and must not have any play elements or overwater structures. The product does not comply with the General Product Safety Regulation.

The product's canopy could cause it to lift off the water if struck by a gust of wind. The child could fall from the product and be injured by impact or drown in the water. The product does not comply with the General Product Safety Regulation.

The product presents a serious risk of injuries as it is supplied with an attachable canopy. In windy conditions, the canopy could cause the product to lift from the water. The child could fall from the product and be injured by impact or by drowning in the water. This product does not comply with the General Product Safety Regulation.

The handlebar stem can easily break due to low mechanical strength. The user can consequently lose control and a fall, suffering injuries. The product does not comply with the General Product Safety Regulation nor with the European standard EN 8098.

The front handbrake may not work correctly because of its too low mechanical strength, This could cause an accident and injuries to the user. . The product does not comply with the General Product Safety Regulation nor with the European standard EN 8098.

The handlebar can easily break due to its low mechanical strength. The child can therefore lose control or the bicycle and fall, resulting in injury. The product does not comply with the General Product Safety Regulation nor with the European standard EN 8098.

The handlebar stem can easily break due to its low mechanical strength. The child can therefore lose control or the bicycle and fall, resulting in injury. The product does not comply with the General Product Safety Regulation nor with the European standard EN 8098.

The handlebar stem can easily break due to its low mechanical strength. The child can therefore lose control or the bicycle and fall, resulting in injury. The product does not comply with the General Product Safety Regulation nor with the European standard EN 8098.

The product is marked as a personal protective equipment but does not have the required compliance documentation or markings to demonstrate that it has been adequately conformity assessed. Therefore, there is no guarantees that the product is safe when used. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The bicycle rack can deflect at the welding between the vertical support and the frame and the vertical support may break close to the welds. The rack can detach from the car which may cause injuries. The product does not comply with General Product Safety Regulation nor the European standard EN 75303.

The centre lock adapters do not guarantee a permanently stable fixation of the brake disc, because the adapter or the locking ring of the adapter can loosen over time and fall onto the axle. As a result, the brake disc can fall off the adapter and become wedged, which can lead to reduced or even total lack of braking performance, leading to injuries. The product does not comply with the requirements of the Machinery Directive.

The adapters do not guarantee a permanently stable fixation of the brake disc because the adapter or locking ring of the adapter loosens over time and may fall onto the axle. As a result, the brake disc may detach from the adapter and become entangled, which may result in reduced or total lack of braking power, leading to injuries. The product does not comply with the General Product Safety Regulation.

The product has a buckle on the chest, which is used to close the harness. This buckle can break during normal use, which may lead to the harness opening and the user falling from a height, resulting in serious injuries. The product does not comply with the Personal Protective Equipment Regulation.

The product has two buckles on the back, which are used to close the harness. These buckles can break during normal use, which may lead to the harness opening and the user falling from a height, leading to serious injuries. The product does not comply with the Personal Protective Equipment Regulation.

The shock-absorbing capacity of the kneepads is insufficient. As a result, the user might suffer injuries in case of an impact. The product does not comply with the Personal Protective Equipment (PPE) Regulation nor with the European standard EN 1621-2.

The strength of the product is inadequate as the carabiner gate may open with a force below 1kN. This can lead to the climber detaching from the safety line and falling from a height. The product does not comply with the Personal Protective Equipment Regulation.

During use, screws can quickly unscrew, which can block progress on snow-covered ground and cause injury. This product does not comply with the General Product Safety Regulation.

Due to a manufacturing defect, the welded joint between the head tube and the down tube may fail. This can cause the frame to break, which could lead to the user to fall and suffer injuries. The product does not comply with the requirements of the Machinery Directive.

The product has too large openings between rungs as well as the climbing net where the body can pass but not the head of a small child and may cause strangulation. Moreover, the frame is not stable and can tip over causing the child to fall and suffer injuries. The product does not comply with the requirements of the Toy Safety Directive nor with the European standards EN 71-8.

The product has too large openings between rungs as well as the climbing net where the body can pass but not the head of a small child and may cause strangulation. Moreover, the frame is not stable and can tip over causing the child to fall and suffer injuries. The product does not comply with the requirements of the Toy Safety Directive nor with the European standards EN 71-1 and EN 71-8.

The metal contacts in the product’s switch mechanism may corrode. leading to the device malfunctioning or turning off. This impedes avalanche rescue and increases the risk of injuries. The product does not comply with the requirements of the Radio Equipment Directive.

The handlebar can move in relation to the steering fork. Moreover, the assembly of the handlebar and its stem can fracture. Additionally, the fork tube of the front fork can crack. Moreover, the saddle cover can separate from the wire base. These defects could lead to injuries for a child riding the bicycle. The product does not comply with the General Product Safety Regulation.

There is a gap between the rear wheel and the mudguard. A child's finger can be pinched between them. The product does not comply with the requirements of the Toy Safety Directive.

The plastic supports can crack if over-tightened. This creates a risk of accidents and injuries. The product does not comply with the General Product Safety Regulation nor with the European standard EN 14682.

The slide/ramp lacks a fixing mechanism and can come loose during use, posing a crushing risk or injuries to a child on or under it. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN EN 71-8.

The goggles’ resistance to compression is insufficient:and can easily break, causing injuries to the user. Moreover, the transmission factor of UV light is too high (up to 89.49%). Consequently, they do not protect the eyes and cause eye damage. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 18527.

An inherent material and/or construction issue can lead to material degradation and cause failure of the product, which can result in severe injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 12277.

The metal cable is not resistant enough and can break with a falling mass of 100 kg. This increases the risk of injuries of a user. The product does not comply with the Personal Protective Equipment Regulation (PPE) nor with the European standards EN 360, EN 354 and EN 813.

The metal cable is not resistant enough and can break with a falling mass of 100 kg. This increases the risk of injuries for the user. The product does not comply with the Personal Protective Equipment Regulation (PPE) nor with the European standards EN 360, EN 354 and EN 813.

The braking force of the rear brake of the bicycle is too weak. This can cause an accident and the child can suffer injuries. The product does not comply with the General Product Safety Regulation nor with the European standard EN 8098.

The breaking force of the rear brake of the bicycle is too weak. This can cause an accident and injuries to the child. The product does not comply with the requirements of the General Product Safety Directive nor with the European standard EN 8098.

The shock-absorbing capacity of the helmet is insufficient. As a result, the user might suffer injuries in case of an impact. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The padding covering the trampoline's springs can move from its initial position, leading the springs and the holes between each spring to be exposed. The user can fall between two springs, resulting in sprains, stretches, fractures or concussion. Moreover, the trampoline is unstable and can easily tip if the user falls against the safety net. Additionally, the safety net is too low, which can lead a user to jump over and fall out of the trampoline, creating a risk of injury. The product does not comply with the requirements of the General Product Safety Directive nor with the European standard EN 71-14.

Children's finger can become trapped in an accessible gap near the starting section of the slide. Moreover, the climbing frame can tip over due to insufficient stability, causing the children to fall and be injured by the fall or by the frame falling on them. The product does not comply with the requirements of the General Product Safety Directive nor with the European standards EN 71-1 and EN 71-8.

The handlebar support and fork can become misaligned. This can result in the rider losing control of the bicycle and falling or crashing. The product does not comply with the requirements of the General Product Safety Directive.

The product has an unsafe canopy attached. If the baby were to be placed in the swim seat and a gust of wind were to catch the canopy, the swim seat would be lifted off the water and the baby could fall from a height, causing injuries. The product does not comply with the General Product Safety Regulation

The handlebar can easily break. The child can therefore fall and suffer injuries. The product does not comply with the General Product Safety Regulation nor with the European standard EN 8098.

The braking force of the front brake is too high. The child can therefore loose balance, fall and suffer injuries. The product does not comply with the requirements of the General Product Safety Directive nor with the European standard EN 8098.

The braking force of the front brake is too high. The child can therefore loose balance, fall and suffer injuries. The product does not comply with the requirements of the General Product Safety Directive nor with the European standard EN 8098

The handlebar can easily break. The child can therefore fall and suffer injuries The product does not comply with the requirements of the General Product Safety Directive nor with the European standard EN 8098.

The slide/climbing board is secured only by insertion in a stabiliser bar. When used by a child, the board can fall on another child present under it, injuring them. Moreover, a child can climb on the rung/ladder and slip through the rungs with both legs, causing a risk of strangulation. The product does not comply with the requirements of the Toy Safety Directive nor with the European standards EN 71-1 and EN 71-8.

The backup brake function does not work for some of the units. Moreover, the primary brake mechanism may fail due to grease degradation in the sealed bearing. The grease reaches the end of its lifecycle before anticipated at the time the device was manufactured.When both the primary and secondary brake engagement mechanisms fail, it can cause the user to fall. The product does not comply with the Personal Protective Equipment Regulation (PPE).

The retention system of the helmet is not adequate, as it elongates too much. If this occurs, the helmet may not remain securely in place during use, increasing risk of head injury in event of a fall. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

Anyone who jumps on the trampoline risks head injury if they collide with the basketball hoop. If any textile parts of the hoop break, the jumper could become entangled, leading to injury or strangulation. Using a ball on the trampoline may increase the risk of injuries. The toy consists of two hoops—one inside and one outside the trampoline. Using both hoops simultaneously on inground or flatground trampolines could increase the risk of user collisions. For non-buried trampolines, there is also an increased risk that a user might crawl under the trampoline while it’s in use to retrieve a lost ball. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-14.

The range of extension of the artificial wrist is excessive, which makes the wrist guard ineffective in the event of a fall and may cause injuries to the user. The product does not comply with the Personal Protective Equipment Regulation (PPE) nor with the European standard EN 14120.

A plastic component at the back of the helmet that holds the chinstrap can break. If this occurs,the helmet may not remain securely in place during an impact or fall, increasing the risk of head injury. The product does not comply with the Personal Protective Equipment Regulation.

The range of movement of the elbow, knee and wrist protection devices is excessive, surpassing the maximum limits. Moreover, the wrist guard restraint system is not continuously adjusted, which makes the wrist guard ineffective in the event of a fall and may cause injuries to the user. The product does not comply with the Personal Protective Equipment Regulation (PPE) nor with the European standard EN 14120.

The suspension fork steerer tubes are too weak and could break without warning. The person on the bicycle could fall, increasing the risk of injuries. The product does not comply with the requirements of the Machinery Directive nor with the European standard EN 15194.

The efficiency of the brakes is too low, not allowing the bicycle to stop safely. That can lead to the loss of control over the bicycle, increasing the risk of accidents and injuries. Moreover, cracks can appear on the handlebars, the frame, the front fork, the saddle and the seat post of the bicycle. If happening during its use, this can cause a person to fall and increase the risk of accidents and injuries. The product does not comply with the requirements of the General Product Safety Directive nor with the European standard EN 4210-2.

The shock-absorbing capacity of the helmet is insufficient. As a result, the user might suffer injuries in case of an impact.Moreover, due to its inadequate shape and structure, the helmet may come off the wearer's head, increasing the risk of head injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

Jumping on the trampoline can cause injuries to the user's head and arms if accidentally jumping into the basketball hoop. Hanging from the basketball hoop or using balls on a trampoline can also cause injuries. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-14.

A child can get pinching or crushing injuries if they get their fingers or toes between the floor and the runner when sitting in the "rocking chair" position.In addition, there are protruding corner posts that could cause children to get stuck with clothes. This can lead to a strangulation risk. Additionally, when the arch is in the climbing position, the distance between the rungs poses a risk of hanging or strangulation, as children could fall through, get their head stuck, and be unable to free themselves. The product does not comply with the requirements of the Toy Safety Directive nor with the European standards EN 71-1 and EN 71-8.

Anyone who jumps on the trampoline can injure their head if they jump into the basketball hoop. If textile parts of the basketball hoop break, the person jumping can become entangled, leading to injuries or strangulation. Use of ball on the trampoline may increase the risk of injuries. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-14.

If the harness does not fit correctly the user may slip out and fall. Moreover, the user can become entangled in the elastic band causing strangulation and be injured if the user trips and falls. Bystanders can also be hurt by the handle spinning. The product does not comply with the requirements of the Toy Safety Directive.

The product lacks instructions for use and the required warning label to warn against using the trampoline in wet conditions. Sprinklers make the trampoline wet, which increases the risk of injuries. The product does not comply with the requirements of the Toy Safety Directive nor with the European standard EN 71-14.

The shock-absorbing capacity of the helmet is insufficient. As a result, the user might suffer injuries in case of an impact. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The product poses a risk of pinching if the arch is turned into the "rocking chair" position. A child can get pinching or crushing injuries if they get their fingers or toes between the floor and the runner when sitting in the "rocking chair" position. The product does not comply with the requirements of the Toy Safety Directive.

Due to its inadequate shape and structure, the helmet may come off the wearer's head, increasing the risk of head injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The peak of the helmet is too rigid and may cause serious neck damage due to induced sudden tilt of the head or mispositioning of the neck. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1384.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1384.

Children's fingers can be entrapped in holes drilled in the frame, and their head and neck can be entrapped in the climbing-net mesh and fall. This increases the risk of strangulation.Moreover, the climbing frame is not stable, a child can fall and suffer injuries. The product does not comply with the requirements of the General Product Safety Directive nor with the European standards EN 71-8.

The strap of helmet may tear off preventing the helmet from staying on the head. In the event of an impact, this could lead to head injuries. Moreover, the shock absorption capacity is not high enough to protect against head injuries in the event of an accident. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1384.

Due to its inadequate shape and structure, the helmet may come off the wearer's head, increasing the risk of head injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1384.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1384.

The cuff of the boot can rotate backwards and overcome the lock mechanism, which would put the wearer at risk of falling and/or injury. The product does not comply with the requirements of the General Product Safety Directive.

When the device is used to secure a follower during mountaineering or climbing, if the follower falls, a potentially damaged follower’s loop may bend open. The follower could then fall to the maximum length of the rope. The product does not comply with the requirements of the General Product Safety Directive.

Incorrect folding of the product may increase the airbag’s inflation time, leading to injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The shock-absorbing capacity of the helmet is insufficient. As a result, the user might suffer injuries in case of an impact. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The bottom bolt of the skate has sharp/rough edge which may cause injuries to the user such as lacerations and cuts. The product does not comply with the requirements of the Toy Safety Directive.

Due to the inadequate attachment system, the helmet does not fit properly on the head. This may cause injury in the event of a fall. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The stem of the bike can loosen or come off, which can lead to a loss of steering, falls and injuries. The product does not comply with the requirements of the General Product Safety Directive.

The straps may become detached from the helmet when pulled, even with relatively little force.This can lead to a risk of injury in the event of a fall. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

There are bare screws on the inside surface of the helmet which could cause a skull fracture/wounds in the event of an accident or fall.The material of the helmet is not tested, too weak and it risks to break in case of an accident. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1385.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, users may suffer head injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1385.

The chain-guard does not completely protect against access to the chain. A child's fingers could get trapped in the chain, leading to injuries. The product does not comply with the requirements of the General Product Safety Directive nor with the European standard EN 8098.

The helmet's fastening system is insufficient. The helmet may slip off the user's head, failing to protect against injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The rope breaks too easily. The user may fall and suffer injuries. The product does not comply with the Personal Protective Equipment (PPE) Regulation, nor with the European standard EN 892.

Corrosion can occur in the chocks.This can significantly reduce its strength and may pose a danger to a climber. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN12270.

Due to a series of defects, the braking system may fail. Consequently, the user may fall and suffer injuries. The product does not comply with the requirements of the Machinery Directive.

The steering tube in the front fork can break, which can cause the user to fall and be injured. The product does not comply with the requirements of the General Product Safety Directive.

The helmet cannot be adjusted without the use of tools and it does not provide sufficient protection from mechanical shocks. The chin strap does not provide sufficient protection because it detaches when subjected to a force which is lower than required. A user may suffer injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 397.

The product has not undergone the conformity assessment involving a competent European conformity assessment body. Consequently, it is not proven that the product fulfils the safety requirements. The product does not comply with the requirements of the Pressure Equipment Directive.

The springs are not sufficiently resistant and may break. The user can slip through the gap between the remaining springs and be injured. Furthermore, a broken spring can also hit and injure other users next to the trampoline. The product does not comply with the requirements of the General Product Safety Directive.

Assembling screws have an insufficient diameter and may break.The scooter may lose parts, and users risk falls and injury. The product does not comply with the requirements of the Machinery Directive nor with the European standards EN 17128, EN 60335-1, and EN 62233.

The saddle joint may break due to material fatigue during use. The user may lose control of the bicycle, fall and suffer injuries. The product does not comply with the requirements of the General Product Safety Directive nor with the European standard EN 15194.

The bolts securing the connection of the steering tube to the footboard can loosen up, which may result in the steering tube and the footboard disconnecting from each other. A user may fall and be injured. The product does not comply with the requirements of the General Product Safety Directive.

The product can easily break and does not adequately absorb impacts, leading to head injury for the user in the event of a fall or impact. The product does not comply with the Personal Protective Equipment Regulation.

The helmet can easily break during an impact, thus not sufficiently protecting the user from injuries to the head. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The helmet can easily break during an impact, thus not sufficiently protecting the user from injuries to the head. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The helmet does not fully absorb impacts, thus not sufficiently protecting the user from injuries to the head. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The helmet can easily break during an impact, thus not sufficiently protecting the user from injuries to the head. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The impact absorption capacity of the helmet is insufficient. In the event of an impact, a child may suffer head injuries. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The helmet can easily break during an impact, thus not sufficiently protecting the user from injuries to the head. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

The shock-absorbing capacity of the helmet is insufficient. As a result, the child might suffer injuries in case of an impact. The product does not comply with the Personal Protective Equipment Regulation nor with the European standard EN 1078.

A carbon cuff can crack or break if the flaps of the cuff are bent too far. Further damage may occur during continuous use which can lead to a complete breakage of the cuff which would put the wearer at risk of falling and/or injury. The product does not comply with the requirements of the General Product Safety Directive.

The bicycle front fork, bike frame, pedals, break system, seat post and handlebars can easily break.Moreover, the breaks do not work properly.:The bike driver can therefore fall and suffer injuries. The product does not comply with the requirements of the General Product Safety Directive nor with the European standard EN 4210-2.

The screw placed in the D-ring eyelets of the climbing harness can break, resulting in a fall leading to injuries to the user. The product does not comply with the Personal Protective Equipment (PPE) Regulation.

The helmet can easily break during an impact, thus not sufficiently protecting the user from injuries to the head. Furthermore, the rear belt connection tears out easily, hence the helmet may slip off; the lack of helmet retention can reduce its effectiveness in the event of impact, causing injuries to the head. The product does not comply with the Personal Protective Equipment (PPE) Regulation and with the European standard EN 1078.

A faulty design of the electrical connector between the battery and the bicycle can cause it to burst, increasing the risk of poor contact. As an electric circuit in the bike melts, the bike will suddenly stop (and not restart), increasing the risk of an accident. The product does not comply with the requirements of the Machinery Directive.

When the training rope is used as intended, the carabiners may open and strike the user's head or eyes through the rubber rope, causing injuries. The product does not comply with the requirements of the General Product Safety Directive.

The product featured poor quality as the power cords, which are exposed to movement between the two motors, are routed through a steel pipe with burr edges at both ends. During the life of the product, the insulation of the power cords will be damaged by the sharp edges to such an extend that the battery may short-circuit and explode during use. As a result, the user might lose control and fall off the scooter and suffer injuries. The product does not comply with the requirements of the Low Voltage Directive and of the European standards EN 60335-1, EN 60335-2 and EN 62133-2.

When used as a kick scooter, the “Y” handlebar joint on the skateboard plank can break due to manufacturing issue. A user can lose balance, fall and get injured. The product does not comply with the requirements of the General Product Safety Directive.

The battery does not have a device that monitors the cells temperature, hence it may overheat during charging, and the hoverboard cover may ignite. The product may cause a fire and the user may suffer burns. In addition, the power cords, which are exposed to movement between the two motors, are routed through a steel pipe with burr edges at both ends. During the life of the product, the insulation of the power cords can be damaged by the sharp edges, the battery may short-circuit and explode during use. As a result, the user might lose control and fall off the scooter and suffer injuries. The product does not comply with the requirements of the of the Low Voltage Directive and of the European standards EN 60335-1, EN 60335-2 and EN 62133.

The battery does not have a device that monitors the cells temperature, hence it may overheat during charging, and the hoverboard cover may ignite. The product may cause a fire and the user may suffer burns. In addition, the power cords, which are exposed to movement between the two motors, are routed through a steel pipe with sharp edges at both ends. During the life of the product, the insulation of the power cords can be damaged by the sharp edges, the battery may short-circuit and explode during use. As a result, the user might lose control and fall off the scooter and suffer injuries. The product does not comply with the requirements of the relevant European standards EN 60335 and EN 62133.

There may be a defect (small cracks may appear) in the carbon fork of the high-speed pedal that could lead to the fork breaking. Therefore, the bike might be unstable, and the user could lose control and fall off, leading to injuries and accidents. The product does not comply with the requirements of the Machinery Directive and the relevant European Standard EN 15194.

The product lacks instructions for use and a warning label to warn against using the trampoline in wet conditions. Because the trampolin becomes wet it can cause injuries. The product does not comply with the requirements of the Toy Safety Directive and the relevant European standard 71-1, 2 and 3.

The protective cap at the end of the bicycles cables are not resistant enough and could easily detach. The user could get injured by the metal threads of the ropes.The rear thread brake is not equipped with the suitable locking elements and the pedal can easily break while in use. Consequently the user could easily fall when normally using the product. The product does not comply with the relevant European standard EN ISO 4210-2.

The battery does not have a device that monitors the cells temperature, hence it may overheat during charging, and the hoverboard cover may ignite. The product may cause a fire and the user may suffer burns. Furthermore, the dimensions of the socket outlet of battery charger are not suitable. The user could touch the accessible live parts and receive an electric shock.In addition, the power cords, which are exposed to movement between the two motors, are routed through a steel pipe with burr edges at both ends. During the life of the product, the insulation of the power cords can be damaged by the sharp edges, the battery may short-circuit and explode during use. As a result, the user might lose control and fall off the scooter and suffer injuries. The product does not comply with the requirements of the Low Voltage Directive and of the relevant European standards EN 60335-1, EN 60335-2 and EN 62133-2.

The battery does not have a device that monitors the cells temperature, hence it may overheat during charging, and the hoverboard cover may ignite. The product may cause a fire and the user may suffer burns.Furthermore, the dimensions of the socket outlet and the flat plug and the insulation between the primary and secondary sides of battery charger are not suitable. The user could touch the accessible live parts and receive an electric shock.In addition, the power cords, which are exposed to movement between the two motors, are routed through a steel pipe with burr edges at both ends. During the life of the product, the insulation of the power cords can be damaged by the sharp edges, the battery may short-circuit and explode during use. As a result, the user might lose control and fall off the scooter and suffer injuries. The product does not comply with the requirements of the Low Voltage Directive and of the relevant European standards EN 60335-1, EN 60335-2 and EN 62133-2.

There are no safety barriers. Consequently, children using the equipment could fall from a height of approximately 2 m and suffer injuries. The product does not comply with the requirements of the General Product Safety Directive and European standard EN 14960-1.

The landing platform is too small. Consequently, children climbing the pyramid may fall and land outside the soft landing platform, on the ground and suffer injuries. Furthermore, the material does not resist to fire, it does not stop burning when the ignition source is removed and it burns rapidly. As a result, there is a risk of fire and burns. The product does not comply with the requirements of the General Product Safety Directive and European standard EN 14960-1.

The battery does not have a device that monitors the cells temperature, hence it may overheat during charging, and the hoverboard cover may ignite. The product may cause a fire and the user may suffer burns.In addition, the product featured poor quality as the power cords, which are exposed to movement between the two motors, are routed through a steel pipe with burr edges at both ends. During the life of the product, the insulation of the power cords will be damaged by the sharp edges to such that in the battery may short-circuit occurs and explodes during use. As a result, the user might lose control and fall off the scooter and suffer injuries. The product does not comply with the requirements of the Low Voltage Directive and of the relevant European standards EN 60335-1, EN 60335-2 and EN 62133-2.

Due to a software error, the fail-safe function may not operate and the electric system may keep the bike in motion when the user tries to brake in case of emergency, leading to injuries. The product does not comply with the requirements of the Machinery Directive and the relevant European Standard EN 15194.

The product featured poor quality as the power cords, which are exposed to movement between the two motors, are routed through a steel pipe with burr edges at both ends. During the life of the product, the insulation of the power cords will be damaged by the sharp edges to such that in the battery may short-circuit occurs and explodes during use. As a result, the user might lose control and fall off the scooter and suffer injuries. The product does not comply with the requirements of the Low Voltage Directive and of the relevant European standards EN 60335-1, EN 60335-2 and EN 62133-2.

The battery does not have a device that monitors the cells temperature, hence it may overheat during charging, and the hoverboard cover may ignite. The product may cause a fire and the user may suffer burns. In addition, the power cords, which are exposed to movement between the two motors, are routed through a steel pipe with burr edges at both ends. During the life of the product, the insulation of the power cords will be damaged by the sharp edges to such that in the battery may short-circuit occurs and explodes during use. As a result, the user might lose control and fall off the scooter and suffer injuries. The product does not comply with the requirements of the Low Voltage Directive and of the relevant European standards EN 60335-1, EN 60335-2 and EN 62133-2.

The product featured poor quality as the power cords, which are exposed to movement between the two motors, are routed through a steel pipe with burr edges at both ends. During the life of the product, the insulation of the power cords will be damaged by the sharp edges to such that in the battery may short-circuit occurs and explodes during use. As a result, the user might lose control and fall off the scooter and suffer injuries. The product does not comply with the requirements of the Low Voltage Directive and of the relevant European standards EN 60335-1, EN 60335-2 and EN 62133-2.

The spokes of the front wheel might be insufficiently tightened. The user could lose balance and fall off leading to injuries and accidents. The product does not comply with the requirements of the General Product Safety Directive and the relevant European standard EN ISO 4210-2.

The toy is not sufficiently stable and could easily tip over, causing injuries to the child. Moreover there is a risk of entrapment because a child can get its head stuck between the sticks of the toy.. The product does not comply with the requirements of the Toy Safety Directive and the relevant European standard EN 71-8.

The product's coupling may detach during normal use. This may cause injuries to the user.

The wear of the webbing can be higher than normal, causing it to get stuck inside the device and tear off during a free fall jump. As a consequence, the jumper may fall to the ground from high height causing fatal or serious injury. /

Water may enter in the product's charger (charging connector), and the product itself (control electronics) is not resistant to moisture nor correctly insulated against water ingress. This can damage the electric components causing it to overheat and catch fire. It may also short circuit and make accessible parts live, and a user may suffer an electric shock, or fall and be injured due to malfunction. The product did not comply with the requirements of the Machinery Directive, nor with the European standards EN 60335-1 and 2, and EN 60529.